On this page in the next paragraph yow will discover lots of sound insight with regards to How to Install a Bathtub Yourself.
Installing a bath tub isn't precisely rocket science, however it does call for solid plumbing, carpentry, as well as often, tiling abilities. Replacing an old tub with a brand-new one is additionally a moderately difficult task. If the old bathtub is conveniently accessible, the task can relocate easily; if you have to open up a wall surface to eliminate the old bathtub as well as place the new bathtub, the task is much harder. In either case, the project is within a home handyman's skills, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. Make certain you have actually qualified yourself for the task as well as fit trying it. As opposed to hiring a specialist to take control of a halfway-completed job, it is better to take into consideration using one prior to you start. Possibilities are you may need an expert plumber to make tube connections.
This short article will certainly help you set up a brand-new bathtub in your washroom if you have already acquired a new tub and also do not require to change the plan of your previous water pipelines.
Your devices and material checklist should comprise the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installment, then the first thing you should do is detach the water supply. After doing so, activate the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome due to the limited access that is frequently the case.
Make use of a container wrench (crowsfoot spanner) or a faucet tool to reverse the nut that links the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will come from the pipelines. Once the supply pipelines have actually been gotten rid of, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single taps from turning during this process. Once the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old securing compound.
Prior to moving on to fit the new taps, contrast the pipe connections on the old taps to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the brand-new taps are plastic, then you will require a plastic port to prevent damages to the thread. One end of the adapter fits on the plastic tail of the faucet and the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, then you will certainly require reducing couplers, which attaches the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washers remain in place in between the faucet as well as the sink. Secure the tap in position with the manufacturer supplied backnut. Once the tap is firmly in place, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap connectors. The previous kind should be connected to the tap ends initially, tightening up just by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been linked.
Installing the Bathtub
Making use of the two wood boards under its feet, position the tub in the required position. The wooden boards are handy in evenly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The following objective is to ensure that the bath tub is leveled all round. This can be achieved by examining the level and readjusting the feet on the bath tub up until the spirit level reads level.
To install taps, fit all-time low of the furthest flexible faucet adapter to the appropriate supply pipe by making a compression sign up with; then do the same for the other faucet.
Switch on the supply of water and check all joints and also new pipework for leakages and tighten them if required. Fill up the tub as well as additionally check the overflow electrical outlet and also the typical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the maker's instruction manual. Tiling and sealing around the bath tub should wait up until the bath tub has actually been made use of at the very least once as this will settle it into its last setting.
Planning for the Setup
To start with, the sustaining structure supplied with the bath must be fitted (if required) according to the producer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the faucet block, it is very important to make sure that if the faucet includes a plastic washer, it is fitted between the bath and the faucets. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps device to prevent pressure on the bathtub.
Fit the flexible faucet ports to the bottom of both taps using 2 nuts and also olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use every one of the supplied washers.
Link the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a similar manner.The bath must now be ready to be fitted in its final setting.
Tiling Around the Bathtub
In the area where the bathroom meets the ceramic tile, it is essential to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can move sufficient to crack a stiff seal, causing the water to permeate the wall in between the bath and the tiling, resulting in difficulties with dampness and feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealants to blend in your fixtures as well as installations. They are sold in tubes and cartridges, as well as are capable of sealing gaps up to a size of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of soaked paper or soft rope. Bear in mind to always fill the bathtub with water prior to sealing, to allow for the movement experienced when the tub is in use. The sealant can split relatively very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are additionally easily available on the marketplace. It is a good idea to fit the tiles making use of waterproof or water-proof adhesive and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you like reading up on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround? Write feedback down the page. We will be pleased to know your ideas about this entry. Hoping that you visit us again in the near future. Loved our entry? Please share it. Help someone else check it out. We cherish reading our article about Installing A Bathtub.
Act, don't delay!